[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

[netCDF #OFP-755631]: Netcdf

Greetings Leif,

Let's try this - set lt_cv_ld_force_load=no before the configure command:

lt_cv_ld_force_load=no ./configure --prefix=/opt/netcdf3/gfortran

Also, before re-configuring, set your environmental flags the following way:

export FC=gfortran
export F77=gfortran
export CFLAGS='-arch i386'
export FFLAGS='-g -O2 -m32'
export FCFLAGS='-g -O2 -m32'

Make sure to execute a make clean before re-configuring.

Cheers!

Sean

> Thank you for the response I tried exporting FFLAGS and CFLAGS as you
> recommended and I still receive the same error messages.  I am using a
> cookbook guide to installing netcdf from Dr. MacCready's website
> http://faculty.washington.edu/pmacc/roms_mac_notes.html and I don't know
> if I am going wrong somewhere else.  Thank you very much for your time.
> 
> Leif
> On 8/26/11 12:29 PM, Unidata netCDF Support wrote:
> > Greetings Leif,
> >
> > Your error log indicates there is a cpu architecture mismatch in your 
> > libraries. Your CFLAGS variable indicates that you would like to build 32 
> > bit libs. If this is the case, you will need to modify both your CFLAGS and 
> > FFLAGS as such:
> >
> >   FFLAGS='-O3 -m32'
> >   CFLAGS='-arch i386'
> >
> > Note that -m32 -m64 flags are for gfortran 32/64-bit; gcc expects -arch 
> > i386 or -arch x86_64.
> >
> > Cheers!
> >
> > Sean
> >
> >> Full Name: Leif Rasmuson
> >> Email Address: address@hidden
> >> Organization: University of ORegon
> >> Package Version: 3.6.3
> >> Operating System: MAC OS 10.6.8
> >> Hardware:
> >>
> >> Description of problem: I am attempting to install netcdf and have been
> >> using the following commands before running the ./configure:
> >>
> >>
> >> d70-134:netcdf-3.6.3 lrasmuson$ export FC=gfortran
> >> d70-134:netcdf-3.6.3 lrasmuson$ export F77=gfortran
> >> d70-134:netcdf-3.6.3 lrasmuson$ export F90=gfortran
> >> d70-134:netcdf-3.6.3 lrasmuson$ export FFLAGS='-O3'
> >> d70-134:netcdf-3.6.3 lrasmuson$ export CFLAGS='-m32'
> >> d70-134:netcdf-3.6.3 lrasmuson$ ./configure --prefix=/opt/netcdf3/gfortran
> >>
> >> the configure appears to run ok but I receive the following errors after
> >> running $ make check
> >>
> >> ld: symbol(s) not found
> >> collect2: ld returned 1 exit status
> >> make[2]: *** [nctst] Error 1
> >> make[1]: *** [check-am] Error 2
> >> make: *** [check-recursive] Error 1
> >>
> >> I have included a more complete copy of the output as an attached text
> >> file if that helps.
> >>
> >> Thank you Leif
> >>
> >>
> >
> > Ticket Details
> > ===================
> > Ticket ID: OFP-755631
> > Department: Support netCDF
> > Priority: Normal
> > Status: Open
> >
> 
> 
> --
> Leif K. Rasmuson
> 
> PhD Student
> Oregon Institute of Marine Biology
> Phone: (253)961-1763
> E-Mail: address@hidden
> ><((((º>`·.¸¸.·´¯`·...¸><((((º>
> 
> 


Ticket Details
===================
Ticket ID: OFP-755631
Department: Support netCDF
Priority: Normal
Status: Open